Bogging on max pitch

Please help My mini cp bogs onaximum pitch Throttle curve is 100% across the board and pitch is 100% - 0 - 100% As soon as I go past 50% (approx) pitch it just bogs and sinks, motor pitch changes as if working hard. If I bring the stick back down I get lift again! Any help would be appreciated...

98 civic d16y7/y8 Bogging

Need help or opinion..I did a d16y7/y8 mini me vtec conversion..now my car bogs like a pos! Running on my stock p2e atm and stock Dx IM, No CEL, burped and flushed coolant system, cleaned iacv, new spark plugs and wires, timing is correct, fuel filter looks ok, fuel pump runs perfect! It bogs really bad after it warms up to running temp.

Mcpx hp05 bogging

I have a mcpx and 7amp flashed esc and I have a horrible bogging problem at the end of my stick. I use a dx8. Is there anyone that can maybe email me there dx8 brushless mcpx set up that uses a hp05? I have adjusted the pitch curve and throttle curve with no luck. Not very programming savy. Thanks for any help!...

s14 ka24de bogs out, can't pass 2k rpms

i have a 5 speed 1995 240sx with obd1 ka, and it bogs out at 2k rpms. Turns right on first click of the key and just recently did a tune up (spark plugs,wires, cap/rotor, and oil). It started bogging last week until i unplugged the battery and plugged it back in and it ran perfect for a week. now it dies out when in first or reverse gear...

Need help- MPFI swap throttle bogs and surges

Completed my mpfi swap two nights ago, it was running fine other than a minor vacuum leak that i bypassed for the moment till i get another hose. Now the idle is surging from 1500 rpm to 1000 rpm, the only code i had was air intaketemp sensor which i replaced, i reset the ecu and replaced the sensor, the code still persist and now my thro...

[$44.99] BOGS Waterproof Footwear by She Steals

BOGS waterproof shoes and boots are designed for women who aren`t afraid to get a little dirty, but don`t want to come home with waterlogged feet and ruined pedicures either. Built to withstand whatever your todo list has in store, BOGS keep your feet dry, comfy, and in control. From an afternoon out in the garden to spending rainy days i...

[$74.99] BOGS Womens Waterproof Boots by She Steals

Tired of ruined shoes and wet, dirty feet after a day of outdoor chores? Treat yourself to the warmth, protection, and style of BOGS Women`s Waterproof Boots. Whether you`re heading to the stables to feed the horses, trudging through the mud to get to the mailbox, or picking weeds in the early morning dew, BOGS are the waterproof, insulat...

Slow Pitch Response?

Hi, I have an issue with my mini P that I'm seeking help with; the collective response is very slow around center. When I change pitch, I have to move the stick quite a bit either positive or negative, before I get a decent response from the heli. I'm running MHS/Scorpion 2580 Kv motor, 15T pinion (vs.the stock 16T) at 100% TC (Mr.Mels he...

tail wag violent during normal mode

OK so I crashed doing a double loop backwards but it hit some weeds only damage to my eyes was main gear. So I change it and check everything like main shaft etc. Go fly and I have a violent tail shake during pitch changes and going up and down on collective doesn't pop like it used to up and down Like it kind of bogs. Like I an robbing...

bogging hp06 v2???

Hello guys, I have a question regarding bogging the motor when pushing the heli, or just going full positive pitch. I wil trying to give as much info as possible. Thanks in part to the help and info I have received from this sight I have a good flying heli. but I have seen a change lately. I have Blade MPC X V2 with a 3-in-1 control unit...

LS Swap into EK, bogs when trynna rev

So Its my first time doing a swap..i put a obd2 ls in to my 98 civic lx i used the stock harness ...so today i starded the car on after i finished putting it in it turned on. So i try to rev it and as soon as i try to tap to rev it bogs..i have 3 plugs unplug..i was told one is for the sensor dats right by the oil pan the other is for the...

Engine bogging issue

Hi guys I need your help on a bogging issue. It's an asp .36 ringed only few days old. The mechanics are an old century hawk pro that I have installed in funkey airwolf fuselage. Broke the engine in as per instructions and went through 3 tanks of fuel without any problems. The moment I installed back in fuselage it started bogging at mid...

z6 intake manifold on y7 bogging issues

Today i did a z6 intake manifold swap on my d16y7. I used the z6 fuel rail y7 tb and y7 injectors. i used a new y7 intake manifold gasket And reused the stock y7 tb gasket because part store said it would take a week to order. The car idles fine and revs up perfect while the cars not moving in neutral, however when i drive it if i go over...

when using CMDeviceMotion, if the device is straight up (pitch = 90), it's really unstable. Anyway to solve this?

I know the (pitch, yaw, roll) coordinate system has its own flaw mathematical-wise. However I really hope something instead or derived from this coordinates can be an alternative. What I am try to do is moving the device (let's say it's an iphone) in the real world and trying to figure out the yaw and pitch regarding to user's eye. Thus,...

Will the talon handle a Scorpion 4025-1100 on this light bird?

I must say when i went with a goblin over a align or gaui I expected a crazy fast heli, i love hard punch outs and hard quick direction changes, Well when you start piecing all these together the quantum just bogs, Ive found at 2900 headspeed and 14* of pitch it feels more like i expected but it runs to hot at those numbers. End up heatin...

Trex 500 Pitch Curves and DX8 setup problems

Hi there, I'm having real trouble setting up my Trex 500 pitch curves with my dx8. I've identified that I would like to get about 0deg at 0%, +6deg at 50% and +10deg at 100%. This is for general flying as i'm only just finished with my training gear on my other helis. The thing is the pitch servo travel is just huge, giving me a -20ish to...

Aileron pitch

I've been trying to set up my new trex 450 pro dfc which has the 3 gx system. I've set the collective pitch to +8 and -8 and when in the set up for ail pitch it's set to the same as collective pitch but when set up is complete it changes and goes to +14 and -14 but the collective pitch stays as normal. I'm using a dx7s...

Is Negative Pitch Necessary?

I was showing my MCPX to a friend who was a helicopter pilot, in Nam, and explaining the controls. When, I got to the part about negative pitch he stated a “real helicopter” does not have negative pitch. Well this got me thinking. I am not interested in flying inverted, at least not now, so what is the benefit in having negative pitch. If...

i think my pitch is messed up??????

Ok people i crashed my 300 x blew out two of my servos so decided to put on align ds 415 sevos in cyclic and ds 425 on the tail.ok now i know when u give positive pitch up the swash goes down is rite. But mine wants to push the heli down at the point and when i go negative pitch it wants to go up............ i have went through every sett...

Futaba t6 pitch question

Im new and I am learning a damn lot!! But I do have a question. I have been reading a lot on here and I always see references to pitch curves using degrees. I thought thats how I would see them referenced in the radio settings, but I see percentage. Now I'm assuming each heli is different and the radio cannot tell you how many degrees of...

How much tail pitch is too much?

I've been having to reduce the tail pitch to get the HC3-SX tail stops working correctly. I usually end up between 14.5 degrees and 18 degrees of pitch for each side (-18 left and +18 right). Since the travel has been reduced significantly I'm starting to worry that some of that tail pitch might be necessary. Does anyone know how much tai...

Brain requests

Thought this might be a good place to put together a request list for future additions to the Brain. I am a total convert but there are a few other things I'd like to see in this unit. Please add to this list as you see fit and please do discuss! Perhaps if it gets a decent response we can get it made a sticky. I'd live to see auto bailou...

Zero pitch (no more???)

Ok ive done the zero pitch deal setup and dx6i "tamer" mcpx settings,months ago!!! Now I guess my questions are: 1.that tamer stuff will not let me fly inverted right?? 2.now that im proficient with all orientations..nose-in..tail in.. fig 8s..etc...etc. Do I try to reverse the pitch change for more "aggressive..3d flying?? 3. I wish to...

New to me Velocity, pitch problem

Hey guys, I'm trying to figure out how to get more pitch out of the head. This is a flybar version and I have everything setup as instructed in the manual for "Intermediate" settings. I had everything at "Advanced", but still couldn't get any more than 10 degrees pitch before the washout base hits the hub. What adjustment gives more overa...

Devo 7e on Phoenix Pitch channel problem

I am able to use Phoenix OK in Normal mode. But in stunt mode the throttle curves settings works OK but the Pitch curves don't. Only positive pitch in upper and lower halves. On this Devo 7e on calibration I can map: Channel 1: Cyclic Pitch Channel 2: Cyclic Roll Channel 3: Throttle and Collective Pitch Channel 6: Tail Rotor Throttle and...

Tail settings on mini v-bar for TREX 500 Pro

G'day guys. Recently my Trex 500 DFC Pro has been driving me up the wall with a very annoying tail blow issue. The model is all stock align combo aside from a scorpion motor (same kv as align motor) and the mini v-bar 5.2 V-bar logs indicate there are no serious vibes in a normal hover flight at idle 1 or idle 2. The heli has started to b...

MINI After-Dark – night activities for this weekend

Thinking of what to do and where to go this weekend? Here’s an option. MINI Malaysia is having its MINI After-Dark event this evening, billed as a “not normal” weekend evening planned for the MINI enthusiast. The event will be happening this Friday and Saturday night (April 12-13) from 8.00 pm to 11.00 pm at all MINI dealerships in the co...

Lynx, Rakon, or Xtreme Pitch Slider/Tail

Ok guys, it's been a few months and I am now in need of a replacement pitch control slider. What are the best/lightest pitch sliders out right now that will work with everything else stock? I may upgrade the whole tail-case at some point but right now only planning to get a pitch control slider. Was originally going to go Lynx but RKH an...

More positive & negative pitch???

I have my travels all set at 100%... Is there a way to get more positive and negative pitch on this 130x?? It flys ok (except for a sloppy pitch slider bearing) but I would LOVE to have more collective pitch. Any ideas????...

Limited negative pitch

According to my pitch gauge I get about -7 to 13 degrees of pitch. I was going to adjust the links until I had equal amounts positive and negative pitch, but I read on this forum that the 300x is supposed to go from -13 to 13, so I was wondering if there was a beastx step to fix this or if I really just need to adjust the linkages.

How do you set up your Blade Pitch

On the FB models, do you use the Trex 250 pitch gauge? Or do you sue the hanging upside down method. I am just wondering how you lock the FB to use a pitch gauge?...

Spektrum DX 6 issue

If you run into this situation: DX 6 and orange 6 ch. Rx on 120 deg. CCPM. I've had cyclic-pitch swash movements to work ok. However collective-pitch swash movement was backwards and if reversed then cyclic went off. Tried reversing Ail. and Elev but this in turn would throw off the pitch. Change pitch swash-mix from +60 to -60 or whateve...

Your opinion on 0 to 100 normal pitch curve

I have taken the HF advice and set my TH pitch curve to 0 25 50 75 100. The only issue I have is that after landing, if I hit TH, the baldes jumpt to full neg.So I am thinking about setting my normal pitch curve to match. My mid-stick throttle setting is 85%. Would bad things happen if I did this? My assumption is that there would only be...

First Robird Hover a Non-Event!

I installed the Robird in the Mini Titan and did the first test hover on lunch today. This was the first time I had flown the Mini in, probably two or three years, the first time I have flown the Thunder Tiger FBL head for it, and the first time I have ever set up and installed a Robird. I went through the instructions, then the videos, t...

Anyone switch from 4020 to 4025 and regret it?

Im thinking of installing a 4025 scorpion, but wonder if anyone has regret it, I just find my quantum bogging to much. This is running the ikon gov which is tuned in but the motor only has so much ummp. Im running 18t, 2800. I just put the 19t back on, and im gonna try a few different things to see if I can keep the heat down with the tal...

Reverse Pitch

So my throttle I push up and the swash goes up, down vice versa. My pitch is reversed push up negative pitch push down positive pitch. Should I reverse my blade grips?...

Cubitek Mini Cube tested and reviewed

We review the Cubitech Mini Cube as it is the world’s first Mini ITX chassis supporting cable management behind the MB tray. With the fully aluminum Mini Cube, this brings Mini ITX to gamers...

Collective/Cyclic Pitch Values

Hey Guys, Just maidened my NX4 today. Great heli! Got a quick question on pitch values. When I set it up, i was only able to get about 11.5 degree collective and 9 degrees cyclic without the swash hitting the headblock on full cyclic/collective pitch, or bottoming on the swash guide at full negative pitch/aft cyclic. Is everyone using the...

【业界资讯】友达光电赶上 iPad mini 屏幕生产需求，开始为mini 2代生产屏幕？

据 Digitimes 报道，苹果供应商友达光电已经克服了长期困扰他们的 iPad mini 显示屏量产跟不上的问题，在目前这代 iPad mini 显示屏的产量上大幅提升。并且相关的生产设施已经为下一代 iPad mini 屏幕的量产打下了坚实的基础。 由于友达在2012年下半年在面板良率控制上遇到很多麻烦，所以最终的 iPad mini 累计出货量低于苹果原先预估的1000万台。不过现在消息人士透露，友达已经克服了这 些问题，在2013年第一季度可以提供高产能，这也就意味着苹果的 iPad mini 的货源将不会跟之前那样一样显得紧张，相应的友达在2013年的面板出货量也会推高。 iPad mini 自去年10月份发布以来，一直处于供货紧张的状态。当时就有消息指出出货紧...

猜测：iPad mini 2或四季度上市_热闻辣评：苹果WWDC发布新品即将揭晓

2013-06-10 05:34:00 作者：蔡文清 ·猜测：iPad mini 2或四季度上市 一句话点评：虽然我们肯定苹果作为全世界最具有能力的电子消费类产品厂商之一的地位， 但采用Retina显示屏幕的iPad mini 2代必须在价格、轻薄、硬件配置这三个方面做出最好的权衡，年内上市的期限对于苹果而 言，真的可以说时间并不算特别宽裕。 近日花旗银行给出了一份报告，称iPad mini 2或将于今年第四季度上市，正如外界传闻的那样，iPad mini 2将配备Retina显示屏，分辨率将达到2048 x 1536。 花旗银行分析师称iPad mini 2将于第四季度上市 （图片来自搜狐） 这份报告称，预计苹果在2013年下半年，发布iPad 5、iPad mini...